Sealey AP2030BB Bedienungsanleitung PDF herunterladen

INSTRUCTIONS FOR:

HEAVY-DUTY WORKBENCH WITH 5 DRAWERS

BALL BEARING RUNNERS

MODEL

AP2030BB

Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and

properly maintained, give you years of trouble free performance.

1. SAFETY INSTRUCTIONS

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.

USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE

DAMAGE AND/OR PERSONAL INJURY, AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.

2. CONTENTS AND SPECIFICATION

1.1 GENERAL SAFETY

! WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are

adhered to when using this bench.

" Locate bench in a suitable working area.

" Keep the work area clean, uncluttered and ensure there is adequate lighting.

! WARNING! Use bench on level and solid ground, preferably concrete. Avoid

tarmacadam since the bench may sink into the surface.

" Keep the bench clean and tidy in accordance with good workshop practice.

" Keep children and unauthorised persons away from the working area.

# DO NOT use the bench for any purpose other than that for which it is designed.

# DO NOT exceed maximum capacity of workbench.

# DO NOT undertake work on the bench without the workpiece being adequately

secured. Use clamps or a vice (not included) to secure the workpiece. Available from

your Sealey dealer.

# DO NOT use the bench out of doors.

# DO NOT get the bench wet or use in damp or wet locations or areas where there is

condensation.

# DO NOT clean the bench with any solvents which may damage the paint surface or the

protective coating on the wooden top.

! The maximum load for each drawer is 25kg, full load for the workbench is 250kg.

AP2030BB - 1 - 260407

2.1 Powder coated steel panels with 40mm wood laminate top. Five drawers. Open shelving for storage of larger items. Supplied flat

packed.

2.2 Table Size (W x D): 1372 x 508mm

Working Height: 865mm

Capacity: 250kg

2.3 Carefully unpack the product and check the contents against the diagram below. Should any items be missing or damaged make

immediate contact with your Sealey dealer.

A . . . .SIDE PANEL H . . . .RIGHT SIDE PANEL M . . . . .DRAWER R . . . . .RIGHT SlDE RUNNER

C . . . .BOTTOM RAIL I . . . . .SUPPORT PANEL O . . . . .CORNER BRACE S . . . . .SCREW (M5x12)

D . . . .TOP RAIL J . . . . .BACK PANEL P . . . . .WOODEN TOP T . . . . .ADJUSTABLE LEG LEVELLER

E . . . .CENTRE SUPPORT K . . . .SHELF Q. . . . .LEFT SIDE RUNNER U . . . . .HEX HEAD SCREW 5/8"

G . . . .LEFT SIDE PANEL

1 2 3 4

Inhaltsverzeichnis

Seite 1 - AP2030BB

INSTRUCTIONS FOR:HEAVY-DUTY WORKBENCH WITH 5 DRAWERS BALL BEARING RUNNERSMODEL:AP2030BBThank you for purchasing a Sealey product. Manufactured to a hi

Seite 2 - 3. ASSEMBLY

3. ASSEMBLYAP2030BB - 1 - 2604071Step 1. As shown in the diagram assemble the two large side panels (A), bottom rail (C) and centre support (E). STEP

Seite 3 - AP2030BB - 1 - 260407

AP2030BB - 1 - 2604073STEP 5. Secure the back panels (J) using 8 screws, 4 in each corner.STEP 4. Screw the top rails (D) onto the front and back. 45

Seite 4

STEP 6. Turn the workbench upside down and screw in the corner braces (O) as shown in the diagram. At each corner attach the leg levellers (T). Slide

Verwandte Modelle: AP2050BB

Kommentare zu diesen Handbüchern

Keine Kommentare

Sealey AP2030BB Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Ausrüstung Sealey AP2030BB herunter. Sealey AP2030BB User Manual Benutzerhandbuch

Inhaltsverzeichnis

Verwandte Modelle: AP2050BB

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Ausrüstung Sealey AP2030BB