Designed for easy installation of fork seals. Limits potential damage caused by other
installation methods to the forks.
DO NOT use the driver for a purpose it is not designed to perform.
DO NOT use the driver if it is damaged, it could scratch the stanchion.
DO NOT make any modifications to the driver.
Maintain the driver in a good clean condition for the best and safest performance.
When not in use, store in a dry location.
Original Language Version
MS016 Issue: 1 - 14/01/15
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
01284 757500
01284 703534
sales@sealey.co.uk
Sole UK Distributor, Sealey Group,
Kempson Way, Suffolk Business Park,
Bury St. Edmunds, Suffolk,
IP32 7AR
www.sealey.co.uk
Web
email
© Jack Sealey Limited
Environmental Protection.
Recycle unwanted materials instead of disposing of them as
waste. All tools, accessories and packaging should be sorted,
taken to a recycle centre and disposed of in a manner which
is compatible with the environment.
Diagram 1 (engaged) 2 (engaged) 3 (disengaged)
Ø"A" 35mm-40mm 40mm-45mm 45mm-55mm
Ø"B" 55mm-60mm 50mm-55mm 65mm-75mm
Always refer to the original manufacturer's manual for assembly and dissassembly of the motorcycle fork seals.
4.1. Measure the stanchion diameter (Ø"A") and the seal ring outer diameter. It may be better that (Ø"B") is less than the seal ring outer
diameter.
4.2. Ensure correct orientation, lubricate and slip the new seal ring over the stanchion and slide it down to the slider housing.
4.3. Fromthespecicationtable,decideonthesetup.Adjustequallyontheslots,thecollarsegmenttobestrepresent(Ø"A).InDiagrams1
and 2 the pins in the slide hammer will be engaged with opposing holes of the other half of the hammer. (In Diagram 3 the engagement
between the pins and holes will be lost. It will be necessary to align, by eye, the two halves of the slide hammer to obtain even seal ring
insertion).
4.4. Holding the slide hammer halves together press the seal into the slider housing. Replace retaining ring if required and repeat all tasks
with the other fork.
INSTRUCTIONS FOR:
FORK SEAL DRIVER
MODEL NO: MS016
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT
CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL
INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
1. SAFETY
2. INTRODUCTION
3. SPECIFICATION
Ø"A"
Ø"B"
Ø"B"
Ø"A"
Ø"A"
Ø"B"
Slide
Hammer
Collet
4. OPERATION
Diagram 1
Diagram 2
Diagram 3
Seal
Ring
As diagram 1
Adjustable
Collet segments
Slide hammer
(2 Seiten)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern