Sealey PS980 Bedienungsanleitung PDF herunterladen

 DO NOT use any tool or lever to turn the ram tommy bar, use

hand effort only.

 DO NOT hit workpiece, or ram, with a hammer if workpiece has not

moved with maximum puller force applied. Use a larger capacity puller.

 Account for all tools and parts being used and do not leave them

in or on the vehicle.

IMPORTANT: Always refer to the vehicle manufacturer’s service

instructions, or proprietary manual, to establish the correct

procedure and data. These instructions for use are provided as a

guide only.

 WARNING! Ensure all Health and Safety, local authority, and

general workshop practice regulations are strictly adhered to

when using tools.

 DO NOT use tools if damaged or worn.

 Maintain the tools in good and clean condition for best and safest

performance.

 Ensure all threads are clean and well lubricated.

 Always check that puller is correctly assembled and is square

with the workpiece.

 If vehicle is raised, ensure it is adequately supported with axle

stands, ramps, etc. as appropriate.

 Wear suitable clothing to avoid snagging. Do not wear jewellery.

Tie back long hair.

 Wear approved eye protection. A full range of personal safety

equipment is available from your Sealey dealer.

 Where possible shield workpiece with canvas or similar to provide

protection against failed parts.

 DO NOT heat puller jaws when heating a gear or bearing as this

will affect the temper and, therefore, the strength of the material.

INSTRUCTIONS FOR:

HYDRAULIC BEARING

SEPARATOR/PULLER SET

MODELS:PS980.V2 PS985.V2

1. INTRODUCTION

Model PS980

Item Part No. Description

1 PS988 Bearing Separator 90 to 105mm

2 PS990 Hydraulic Ram, 10 ton

3 PS982/9014 Beam

4 PS982/9016 Rod, Main & Extension, 2 off each

- PS982/8013 Centre Adaptor (not shown)

Model PS985

Item Part No. Description

1 PS989 Bearing Separator 120 to150mm

2 PS990 Hydraulic Ram, 10 ton

3 PS985/03 Beam

4 PS985/04 Rod, Main & Extension, 2 off each

- PS985/05 Plug (not shown)

- PS982/8013 Centre Adaptor (not shown)

- PS982/8014 Ram Extension, 50mm (not shown)

- PS982/8015 Ram Extension, 100mm (not shown)

PS982.V2-RK Repair Kit for PS990 Ram (not supplied)

PS982/OIL 15grm single refill of oil (Not shown, not supplied).

3. SAFETY INSTRUCTIONS

2. CONTENTS & PARTS

1.1. INTRODUCTION

PS980 has a cast puller yoke and a forged bearing separator. The

separator covers bearing diameters from 90 to 105mm and the extension

rods provide a maximum reach of 420mm. The 10 ton hydraulic ram is

also compatible with sets PS981.V2 and PS982.V2. The PS985.V2 is

similar to PS980.V2 except that the splitter covers bearings from 120 to

150mm diameter and ram extensions and a plug are included.

PARTS LIST

Issue Date:- 12/05/05

Issue No.:- 3

4. INSTRUCTIONS FOR USE

fig.1

fig.2

 WARNING! Ensure that you read, understand and apply the

safety instructions in Section 2.

4.1. Confirm that the bearing is retained by interference fit (parallel

or taper) only.

4.2. Assemble splitter around rear of bearing and clamp together using

the studs and nuts (fig.1.A & B) provided.

4.3. Screw the fully threaded ends of the two puller rods (fig.1.C)

into the splitter.

4.4. Remove nuts (fig.1.D) from free ends of rods and place yoke

(fig.1.E) over thread shanks.

4.5. Retain yoke with flat washers provided (fig.1.F) and nuts, but

do not tighten at this stage.

4.6. Adjust ram T-handle (fig.2.A) so that tommy bar (fig.2.B) is

approximately 80mm above ram end cap (see fig.2) and screw

ram body into yoke until ram piston (fig.1.G) contacts end of

shaft. If shaft has a ‘centre’ machining fit centre adaptor to

piston before screwing ram down. If ram will not reach shaft

use extension piece(s). Note: Only use centre adaptor where

end of shaft has a matching ‘centre’ machining. PS985

contains a plug which provides a thrust pad for the piston

in applications where the shaft is hollow.

4.7. Adjust position of yoke to get ram piston on shaft centre and

then tighten yoke retaining nuts.

4.8. Turn T-handle clockwise, by hand only, to pull workpiece from shaft.

4.9. Do not screw T-handle in further than 25mm (1”) from end of the

ram (see fig.2). If workpiece requires additional movement then

unscrew T-handle to 80mm from end of ram, screw ram body

down so that centre adaptor again contacts shaft and then

continue to draw workpiece up shaft.

IMPORTANT: The maximum safe load for the puller can be

achieved by hand effort alone. The use of tools or levers on

the tommy bar to increase the load will damage the splitter

and may result in injury. Such misuse will also invalidate the

warranty.

 WARNING! If the workpiece does not move when maximum

puller force is applied, DO NOT hit it, or the puller, in an

attempt to jar it free. Damage to puller/workpiece and

personal injury may result. Use a larger capacity puller.

PS980.V2 & PS985.V2 ISSUE No:1 17/12/08

1 2

Inhaltsverzeichnis

Seite 1 - PS980.V2 PS985.V2

 DO NOT use any tool or lever to turn the ram tommy bar, use hand effort only. DO NOT hit workpiece, or ram, with a hammer if workpiece has n

Seite 2 - 01284 703534

5. MAINTENANCEfig.3fig.45.1. GENERAL5.1.1. Keep all items clean and lightly oiled. Keep all threads free from grit and lubricate the ram reg

Verwandte Modelle: PS985 | PS990 | VS0288 | RE99/09 | RE99/10 | PS982 | HP10 | HP5 | PS981 |

Kommentare zu diesen Handbüchern

Keine Kommentare

Sealey PS980 Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Für das Auto Sealey PS980 herunter. Sealey PS980 User Manual Benutzerhandbuch

Inhaltsverzeichnis

Verwandte Modelle: PS985 | PS990 | VS0288 | RE99/09 | RE99/10 | PS982 | HP10 | HP5 | PS981 |

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Für das Auto Sealey PS980