Sealey DAS149 Bedienungsanleitung PDF herunterladen (Seite 2)

LEAD PAINT WARNING!

Paint once contained lead as a traditional ingredient. The dust from the removal of such paint is toxic if inhaled or ingested and must, therefore,

be avoided. The following action must be taken before using the sander on a surface that you suspect may have contained lead in the paint.

1. User must determine potential hazard relating to age of paint to be removed. (Modern paints do not contain lead).

2. DANGER! Keep all persons and pets away from the work area. The following are particularly vulnerable to the effects of lead paint dust:

Expectant women, babies and children.

3. We recommend personal protection by using the following safety items:

a) Paint Spray Respirator

b) PE Coated Hooded Coverall

c) Latex Gloves

4. Take adequate measures to contain the paint dust, flakes, and scrapings.

5. Continue to wear safety equipment as in 3 above, and thoroughly clean all areas when task is complete. Ensure that paint waste is disposed of,

in sealed bags or containers, according to local authority regulations.

Model No:............................................. DAS149

Power:................................................... 600W

No load speed:...................................... 1500-6800rpm PADS: DAS149

Orbit size:.............................................. ø8mm Optional Pad: PTC/150A Stick-on (Firm)

Pad:....................................................... ø150mm Optional Pad: PTC/150SA (supplied) Stick-on(Soft)

Thread:.................................................. 5/16”UNF Replacement Pad: PTC/150VA

Weight:.................................................. 2.26 kg

Vibration:............................................... 2.3m/s²

Uncertainty:............................................1.15m/s²

Noise power:..........................................91dB(A)

Noise pressure:................................... 80dB(A)

 WARNING! Before use, ensure that you have read and understood Section 1 Safety Instructions.

5.1. Attach the correctly rated sanding disc (not supplied) to the sanding pad.

5.2. Plug the sander into the mains power supply.

5.3. Ensure that the speed scroll switch is set to the lowest setting before starting the sander (fig.1). Grip the handle and turn on by pushing

switch (fig.1) forward. Let go of the switch and the machine will continue running. Increase the speed of the sander using the variable

switch located at the rear of the sander (fig.1).

Note: The sander is designed for dry use only. DO NOT use with water or any other liquids.

 WARNING! DO NOT plug sander into the mains power supply before it is fully assembled.

Screw the sanding pad onto the spindle (fig.1.3). To remove pad, hold spindle with the spanner supplied whilst unscrewing the pad.

 Avoid unintentional starting.

 DO NOT use the sander for a task it is not designed to perform.

 DO NOT operate the sander if any parts are damaged or missing. This may cause failure and/or injury.

 WARNING! DO NOT sand any materials containing asbestos.

 DO NOT carry the sander by the electrical cable.

 DO NOT connect to a standard vacuum cleaner to extract dust as damage to the cleaner may result.

 DO NOT get the sander wet or use in damp or wet locations.

 DO NOT use the sander with water, the sander is for dry use only.

 DO NOT operate the sander if you are tired or under the influence of alcohol, drugs or intoxicating medication.

 DO NOT use where there are flammable liquids, solids or gases such as paint solvents or waste wiping or cleaning rags.

 DO NOT leave the sander running unattended.

 DO NOT carry the sander with your finger on the power switch.

 When not in use disconnect from the power supply and store in a safe, dry, childproof area.

 WARNING! The warnings, cautions and instructions in this manual cannot cover all possible conditions and situations that may occur. It

must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be applied

by the operator.

Lightweight, compact sander with variable speed control from 1500 to 6800rpm. Dual action orbit of Ø8mm helps cover more surface during use.

Powered by a 600W motor with a slide on/off switch on top. Soft-grip for added comfort. Supplied with 1.9mtr mains cable.

3. SPECIFICATION

2. INTRODUCTION

4. ASSEMBLY

5. OPERATION

fig.1

Original Language Version

DAS149 | Issue: 2S - 23/12/14

1 2 3 4

Kommentare zu diesen Handbüchern

Keine Kommentare

Sealey DAS149 Bedienungsanleitung Seite 2

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Elektrowerkzeuge Sealey DAS149