Sealey ES450 Bedienungsanleitung PDF herunterladen

Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions

and properly maintained, give you years of trouble free performance.

1. SAFETY INSTRUCTIONS

INSTRUCTIONS FOR:

ENGINE STAND

450kg

Model No:

ES450.V2

PARTS LIST

ITEM PART NO. DESCRIPTION

1 ES450.V2-01 MAIN POST

3 ES450.V2-03 SIDE LEG, FIXED

4 ES450.V2-04 BOLT (1/2”X3”)

5 ES450.V2-05 HEAD MOUNTING PLATE

6 ES450.V2-06 LOCKING PIN

7 ES450.V2-07 MOUNTING ARMS

8 ES450.V2-08 BOLT (1/2”X2 1/2”)

9 ES450.V2-09 FLAT WASHER 1/2”

10 ES450.V2-10 NUT (H3X1/2NC)

11 ES450.V2-11 LOCKING WASHER 1/2”

12 ES450.V2-12 FLAT WASHER 3/8”

14 ES450.V2-14 CASTER WHEEL

15 ES450.V2-15 NUT 3/8NC

17 ES450.V2-17 FLAT WASHER 3/4”

19 ES450.V2-19 LOCKING CLIP

20 ES450.V2-20 MAIN BEAM

21 ES450.V2-21 CASTOR LEG

22 ES450.V2-22 MAIN POST LABEL

23 ES450.V2-23 WHEEL 4”

24 ES450.V2-24 BOLT (3/8”X2 3/4”)

25 ES450.V2-25 LOCK WASHER 3/8”

26 ES450.V2-26 HANDLE (NOT SHOWN)

ES450.V2 - 1 - 031207

Note: All the following numbers refer to Fig.1 and parts list

below.

2.1. Remove mounting plate (5) from main post (1).

2.2. Loosely attach main post (1) to side leg (3) with bolts (24),

washers (12 & 25) and nuts (15).

2.3. Slide main beam (20) into base of main post (1) and loosely

secure with bolt (4).

Note: Main beam (20) must be assembled with bracket (A) as

shown.

2.4. Fit castor leg (21) to main beam (20) with bolts (24), washers

(12 & 25) and nuts (15).

Note: Castor leg (21) must be fitted with castor mounting

holes facing downward.

2.5. Tighten all nuts/bolts.

2.6. Fit castors (14) to castor leg (21) with nuts (10) and washers

(11 & 17).

2.7. Slide wheels (Fig.2.23) onto pins on wheel leg (3) and retain

with washers (17) and locking clip (19).

Note: Wheel hubs are not symmetrical - fit with longer hub

inward.

2.8. Refit mounting plate (5) to main post (1) and locate with

locking pin (6).

2.9. Attach the four mounting arms (Fig.3.7) to mounting plate (5)

with bolts (8), washers (9 & 11) and nuts (10).

2.10. Insert handle (26, NOT SHOWN) through hole in stem of

mounting plate (5).

 WARNING! Ensure all Health and Safety, local authority, and general workshop

practice regulations are strictly adhered to when using this equipment.

 Before using the stand ensure it is in good working order.

 Replace or repair damaged parts. Use recommended parts only. Unauthorised

parts may be dangerous and will invalidate the warranty.

 Keep the stand clean for best and safest performance.

 Locate the stand in a suitable work area, keep area clean and tidy and

free from unrelated materials. Ensure there is adequate lighting.

 Use on a firm, level surface capable of sustaining the stand and the load.

 Maintain correct balance and footing. Ensure the floor is not slippery and

wear non-slip shoes.

 Ensure all non-essential persons keep a safe distance whilst the stand is in

use.

 Lock mounting plate in position with locking pin before fixing a load and ensure

the load is centred and securely mounted on the mounting plate.

 When an engine is mounted, take the weight of the engine on the handle

before removing the locking pin.

 Ensure the stand and load are stable.

 To move a loaded stand, steady the load and push from behind the main

post of the stand so that the castor wheels are ahead of the load.

 DO NOT pull the unit backwards, or push from the side, as this may cause

the stand to tip.

 Ensure surface over which the stand is to travel is strong enough to take

the stand and load and that it is not cracked, uneven or obstructed.

 DO NOT use unit if damaged.

 DO NOT allow untrained persons to use the stand.

 DO NOT exceed the rated capacity of 450kg.

 DANGER! DO NOT work under an engine mounted on the stand.

 DO NOT use the stand for purposes other than those for which it is designed.

 When not in use store stand in a safe, dry, childproof area.

2. ASSEMBLY

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS. USE THIS PRODUCT

CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND

WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.

SPECIFICATION:

Max capacity ........... 450kg

Width ..................... 790mm

Length.................... 950mm

Height .................... 930mm

sales@sealey.co.uk

01284 757500

01284 703534

Sole UK Distributor

Sealey Group,

Bury St. Edmunds, Suffolk.

www.sealey.co.uk

Web

WHEEL HUB FACING

INWARDS

REAR WHEEL ASSY.

Fig.1

Fig.2

Fig.3

ES450.V2 1

Inhaltsverzeichnis

Seite 1 - ES450.V2

Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructi

Kommentare zu diesen Handbüchern

Keine Kommentare

Sealey ES450 Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Werkzeug Sealey ES450 herunter. Sealey ES450 User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Werkzeug Sealey ES450