Sealey VSE5509 Bedienungsanleitung PDF herunterladen

Original Language Version Original Language Version

INSTRUCTIONS FOR:

BMW REAR BALL JOINT TOOL

MODEL NO: VSE5509.V2

1. SAFETY INSTRUCTIONS

Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to

these instructions and properly maintained, give you years of trouble free performance.

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL

REQUIREMENTS, WARNINGS AND CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE

PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY

AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.

2.1 Introduction

Designed to remove and install press-fit rear suspension

ball joints in situ, on BMW 5 and 7 Series. These joints

are sometimes referred to as 'bushes' but are true ball

joints.

2.2 Applications

BMW ................ E39 - 5 Series ................E38 - 7 Series

2. INTRODUCTION & APPLICATIONS

 WARNING! Ensure Health and Safety, local authority

and general workshop practice regulations are adhered

to when using tools.

 DO NOT use the kit if any parts are missing or

damaged.

 DO NOT use the rear ball joint tool for any purpose

other than that for which it is designed.

 Maintain the tool components in good and clean

condition for best and safest performance.

 Ensure that a vehicle which has been jacked up is

adequately supported with axle stands.

 Wear approved eye protection. A full range of

personal safety equipment is available from your

Sealey dealer.

 Wear suitable clothing to avoid snagging. Do not

wear jewellery and tie back long hair.

 Keep children and other unauthorised persons

away from the working area.

 Ensure there is adequate lighting prior to using the

ball joint tool.

IMPORTANT: These instructions are provided as a

guide only. Always refer to the vehicle manufacturer’s

service instructions, or a proprietary manual, to

establish the current procedure and data.

VSE5509.V2 Issue No.1 07/02/13

VSE5509.V2 Rear Suspension Ball Joint tool comprises:

Item Description Part No.

1 Force Screw VSE5509.V2-01

2 Force Nut VSE5509.V2-02

3 Removal Driver VSE5509.V2-03

4 Removal Receiver VSE5509.V2-04

5 Installation Driver VSE5509.V2-05

6 Installation Anchor VSE5509.V2-06

3. CONTENTS/PARTS LIST

fig.1

fig.2

4. INSTRUCTIONS

4.3 Installing a new ball joint

Prior to installing the new ball joint ensure that

the ball joint housing is clean.

4.4 Removing the old ball joint

Using the component configuration indicated

above in fig.4, assemble the parts to the ball joint

housing.

4.4.1 Ensure that the flat head of the force screw (1) is

fully inserted into the slot in the face of the

installation anchor component (6).

4.4.2 Also ensure that the driving face of the force nut

(2) bears onto the bearing mounted in the

installation driver component (5).

4.4.3 Note: The installation driver component (5) must

be positioned to drive the new ball joint into place

towards the back of the vehicle.

4.4.4 Reinstall the snap retaining ring and re-assemble

the vehicle suspension in accordance with

procedures laid down in the manufactuer's

service manual.

IMPORTANT: These instructions are provided as a

guide only. Always refer to the vehicle manufacturer’s

service instructions, or a proprietary manual, to

establish the current procedure and data.

4.1 Preparation

With the vehicle properly supported and

accessible, remove the rear wheels. Making

reference to the vehicle manufacturer's service

instructions remove the swinging arm assembly

and the bolts which pass through the ball joints.

4.2 Removing the old ball joint

Using the component configuration indicated

below in fig.3, assemble the parts to the ball joint

housing. (See also fig.1).

4.1.1 Ensure that the flat head of the force screw (1) is

fully inserted into the slot in the face of the driver

component (3).

4.1.2 Also ensure that the driving face of the force nut

(2) bears onto the bearing mounted in the

receiver component (4).

4.1.3 Remove snap retaining ring from the ball joint.

4.1.4 Note: The driving component (3) must be placed

to drive the ball joint out towards the front of the

vehicle.

fig.3

fig.4

VSE5509.V2 Issue No.1 07/02/13

NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component

parts without prior notice. IMPORTANT: No liability is accepted for incorrect use of this product. WARRANTY: Guarantee is 12

months from purchase date, proof of which will be required for any claim. INFORMATION: For a copy of our catalogue and latest

promotions call us on 01284 757525 and leave your full name, address and postcode.

01284 757500

01284 703534

[email protected]

www.sealey.co.uk

Web

Sole UK Distributor,

Sealey Group, Kempson Way,

Suffolk Business Park,

Bury St Edmunds, Suffolk, IP32 7AR

Force screw maximum load 150Nm. Exceeding this load will shorten the life of the force screw. The force

screw is considered to be a consumable item and is NOT covered under warranty.

VSE5509.V2 1

Inhaltsverzeichnis

Seite 1 - VSE5509.V2

Original Language Version Original Language VersionINSTRUCTIONS FOR: BMW REAR BALL JOINT TOOL MODEL NO: VSE5509.V2 1. SAFETY INSTRUCTIONSThank you f

Kommentare zu diesen Handbüchern

Keine Kommentare

Sealey VSE5509 Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Werkzeug Sealey VSE5509 herunter. Sealey VSE5509 User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Werkzeug Sealey VSE5509